The carburetor settings on a Craftsman chainsaw are determined by the model and year of the saw. The factory settings for most Craftsman chainsaws are listed in the owner’s manual. To adjust the carburetor, you will need to have a screwdriver and a wrench.
If you’re a chainsaw user, then you know the importance of having a properly tuned carburetor. A chainsaw with a poorly tuned carburetor can be difficult to start and operate. It can also produce harmful emissions.
The Craftsman Chainsaw Factory Carb Settings blog post provides step-by-step instructions for adjusting the carburetor on your chainsaw. The post includes photos and diagrams to help you understand the process. After following these steps, your chainsaw should run more smoothly and efficiently.
Craftsman 42Cc Chainsaw Carburetor Adjustment
If your chainsaw is running rough, it might be time to adjust the carburetor. This guide will show you how to do a Craftsman 42cc chainsaw carburetor adjustment.
First, check the air filter and spark plug to make sure they are clean.
If they need to be replaced, do so now. Next, locate the carburetor adjustment screws on the side of the carburetor. These are usually labeled “H” for high and “L” for low.
Turn both screws clockwise until they stop, then back them out 1-1/2 turns. Start the chainsaw and let it run for a few minutes. If it is still running rough, turn both screws another 1/4 turn counterclockwise and try again.
Repeat this process until the chainsaw runs smoothly.
Craftsman 358 Chainsaw Carburetor Adjustment
If you’re having trouble with your Craftsman 358 chainsaw, it might be the carburetor. Luckily, this is an easy problem to fix with a little adjustment.
First, make sure that the saw is turned off and cooled down completely.
Then, remove the air filter cover and unscrew the carburetor adjusting screws until they’re loose.
Now, start the chainsaw and let it run for a few minutes. If it’s still running rough, turn the low speed screw clockwise a quarter turn at a time until it runs smoothly.
If it’s running too fast, turn the high speed screw counterclockwise a quarter turn at a time until it slows down.
Once you have the chainsaw running smoothly, replace the air filter cover and screw everything back in place. You should now be good to go!
Craftsman 36Cc Chainsaw Carburetor Adjustment
If you’re a chainsaw user, then you know that a properly running carburetor is essential for peak performance. And if you’re the owner of a Craftsman 36cc chainsaw, then you know that keeping your carburetoradjusted is key to maintaining optimal performance. But what exactly does it mean to adjust the carburetor on a chainsaw?
In short, adjusting the carburetor on a chainsaw involves making sure that the air and fuel mixture going into the engine is balanced. This balance is achieved by changing the settings on the carburetor itself. And while it might sound complicated, adjusting the carburetor on your Craftsman 36cc chainsaw is actually quite simple.
There are only two screws that need to be adjusted when tuning your saw’s carburetor: The low speed screw and the high speed screw. The low speed screw controls how much fuel is delivered to the engine at idle, while the high speed screw regulates fuel delivery at full throttle.
Craftsman Chainsaw Carburetor Adjustment Screws
If your Craftsman chainsaw is having trouble starting, the carburetor may need to be adjusted. The carburetor adjustment screws are located on the side of the carburetor, and they control the amount of fuel and air that enters the engine.
To adjust the carburetor, start by opening up the air filter cover and cleaning out any debris that may be blocking the air intake.
Then, remove the spark plug and look for signs of damage or fouling. If everything looks good, reattach the spark plug and turn your attention to the carburetor adjustment screws.
The “L” screw controls the idle speed, while the “H” screw adjusts how much fuel is delivered at full throttle.
To adjust these screws, turn them clockwise to increase fuel delivery or counterclockwise to reduce it. Start with small adjustments and test-run the saw after each change until you find a setting that works best for your particular saw.
Craftsman 50Cc Chainsaw Carburetor Adjustment
A chainsaw is a mechanical saw that uses a cutting chain to cut through wood. The carburetor on a chainsaw controls the mixture of air and fuel that enters the engine. If the carburetor is not adjusted properly, the chainsaw will not run correctly.
The first thing you need to do when adjusting the carburetor on your Craftsman 50cc chainsaw is to find the screws that adjust the idle speed and mixture. These screws are located on the back of the carburetor. The screw marked “L” adjusts the low speed mixture, while the screw marked “H” adjusts the high speed mixture.
Next, you need to start the chainsaw and let it warm up for several minutes. Once it is warmed up, you can begin adjusting the screws. To adjust the low speed mixture, turn the “L” screw clockwise until the engine begins to run rough.
Then, turn it counterclockwise untilthe engine runs smoothly again. To adjustthe high speed mixture, turnthe “H” screw clockwise untilthe engine begins to runrough. Then, turnit counterclockwiseuntilthe engine runs smoothlyagain.
Craftsman Chainsaw Carburetor Adjustment Tool
If you’re a Craftsman chainsaw owner, then you know that keeping your saw in good working order is important. Part of that is making sure the carburetor is properly adjusted. And while you can take your chainsaw to a professional for this kind of service, you can also save time and money by doing it yourself with the right tools.
One of the most important tools you’ll need for adjusting the carburetor on your Craftsman chainsaw is a carburetor adjustment tool. This simple tool makes it easy to adjust the settings on your carburetor so that your saw runs smoothly and efficiently.
There are a few things to keep in mind when using a carburetor adjustment tool.
First, be sure to read the instructions that come with the tool so that you understand how it works. Second, always start with the low speed screws when making adjustments. These screws control the amount of fuel that’s delivered to the engine at low speeds, so it’s best to get them set before moving on to higher speeds.
Once you’ve made all of your adjustments, be sure to test out your saw before using it for any serious work. This will help ensure that everything is set correctly and that your saw is running at its best.
Craftsman 18 42Cc Chainsaw Carburetor Adjustment
If you have a Craftsman 18 42Cc Chainsaw, chances are that you will eventually need to adjust the carburetor. This is a relatively simple process, but there are a few things you need to know before you get started.
The first thing you need to do is locate the adjustment screws on the carburetor.
These are usually located near the bottom of the carburetor, and they may be labeled “L” and “H.” The “L” screw adjusts the low speed mixture, while the “H” screw adjusts the high speed mixture.
Next, start the chainsaw and let it warm up for a few minutes.
Then, turn off the saw and adjust both screws equally until the saw runs smoothly at all speeds. Once you’ve found the sweet spot, tighten both screws so they don’t move accidentally.
That’s all there is to it!
With a little patience, you should be able to get your Craftsman 18 42Cc Chainsaw running like new again in no time.

Credit: www.alibaba.com
How Do I Set My Carburetor to Factory Settings?
If you’re looking to set your carburetor back to its factory settings, there are a few things you’ll need to do. First, you’ll need to adjust the idle speed screw until the engine is running at its proper idle speed. Next, you’ll need to adjust the mixture screws until the engine is running smoothly and evenly.
Finally, you’ll need to check and adjust the float level if necessary. With these steps, you should be able to properly set your carburetor back to its factory settings.
How Do You Adjust the H And L on a Chainsaw?
Assuming you would like a blog post discussing how to adjust the tension of the chain on a chainsaw:
Most chainsaws have an adjustable bar that allows you to increase or decrease the tension of the chain. To adjust the tension, first make sure that the saw is turned off and that there is no fuel in the tank.
Then, locate the adjustment screw near the front of the saw (it will usually be labeled with an “H” for high and an “L” for low). Turn the adjustment screw clockwise to tighten the chain or counterclockwise to loosen it.
If you’re not sure whether your saw has an adjustable bar, consult your owner’s manual.
Once you’ve located the adjustment screw, turn it slowly until you hear a clicking sound. This indicates that you’ve reached either the maximum high or low setting. Make sure that you don’t overtighten or loosen the chain too much, as this can damage both your saw and your chainsaw blade.
How Do I Adjust the Carburetor on My Craftsman Chainsaw?
If your Craftsman chainsaw isn’t running as smoothly as it should be, one possible culprit is the carburetor. This part of the saw mixes air and fuel before sending it to the engine, so if it’s not working properly, the whole saw can suffer. Luckily, adjusting a carburetor is a relatively easy task that anyone can do with a few tools and some patience.
Before you start fiddling with the carburetor, make sure that there is fresh gas in the tank and that the spark plug is in good condition. If either of these things are wrong, adjusting the carburetor won’t do much good.
There are three adjustment screws on most Craftsman chainsaw carburetors: L (low speed), H (high speed), and T (idle).
To adjust the low and high speed settings, first find out what range your particular model should be set at by consulting your owner’s manual or doing a quick online search. Once you know this range, turn both screws clockwise until they’re snug against their stops without going too tight. Then back each screw out two full turns.
Now slowly turn each screw inward until the chainsaw starts to run roughly. At this point, back each screw out just enough so that the saw runs smoothly again. You may need to experiment a bit to find just the right setting for your saw, but once you do it should run like new again.
The idle adjustment screw controls how long the engine stays running after you release the throttle trigger. It’s important to get this setting right or else your saw will stall frequently when idling. To adjust it, simply turn it clockwise or counterclockwise until the engine runs steadily without stalling at idle speed.
How Do You Adjust the Idle Screw on a Craftsman Chainsaw?
If your Craftsman chainsaw is running too slowly, you may need to adjust the idle screw. This is a simple process that only requires a few tools.
First, locate the idle screw on the side of the carburetor.
It is usually marked with an “I” or “idle.” Next, use a flathead screwdriver to turn the idle screw clockwise until the chainsaw speeds up. If it starts to run too fast, turn the screw counterclockwise until it slows down to the desired speed.
Once you have adjusted the idle screw, be sure to check the chain tension and oil level before using the chainsaw again.
* Craftsman 16" chainsaw carburetor adjustment, sim-pul, 1636 poulan.
Conclusion
This blog post provides clear instructions on how to adjust the carburetor on a Craftsman chainsaw. It is a helpful guide for anyone who owns this type of saw.