If your chainsaw is running too lean, meaning there’s not enough fuel mixture reaching the engine, you’ll need to adjust the carburetor. You can do this from scratch by first adjusting the low speed needle 1/8th to 1/4th turn clockwise. If your chainsaw is still running lean, turn the low speed needle another 1/8th to 1/4th turn clockwise.
Repeat this process until the saw runs smoothly.
- The chainsaw carburetor regulates the mixture of fuel and air in the engine
- If the carburetor is not adjusted properly, the chainsaw will not run correctly
- To adjust a chainsaw carburetor from scratch, you will need to know what type of carburetor your saw has
- Once you know what type of carburetor your saw has, you can start adjusting it
- To adjust the high speed screw, turn it clockwise to lean out the mixture or counterclockwise to richen the mixture
- To adjust the low speed screw, turn it clockwise to richen the mixture or counterclockwise to lean out the mixture
- 7 Be sure to check your owner’s manual for specific instructions on how to adjust your particular model of chainsaw

Credit: www.youtube.com
How Do You Tune a Carburetor from Scratch?
If you’re starting from scratch, the first thing you need to do is identify all of the parts of the carburetor. The most important part is the float bowl, which contains fuel and regulates how much fuel gets into the carburetor. The next most important part is the jet, which controls how much air gets into the carburetor.
Finally, there’s the throttle body, which controls how much air and fuel mixture gets into the engine.
The first step in tuning a carburetor is to adjust the float level. This ensures that the correct amount of fuel is being delivered to the carburetor.
Next, you’ll need to adjust the jets. These control both how much air and fuel get into the carburetor. Start with smaller jets and work your way up until you find a good balance between air and fuel delivery.
Finally, adjust the throttle body to control how much mixture gets into the engine.
How Do You Adjust the H And L on a Chainsaw?
If you’re having trouble starting your chainsaw, or if it’s running roughly, one of the first things you should check is the H and L settings. These refer to the high and low speed settings on the carburetor, and adjusting them can make a big difference in how your saw runs. Here’s a quick guide to adjusting the H and L on your chainsaw.
First, locate the screws that control the high and low speed settings. On most saws, these will be marked “H” for high and “L” for low. Once you’ve found them, use a screwdriver to turn each one clockwise until it stops.
Next, start your chainsaw and let it idle for a minute or so. Then, slowly turn the “L” screw counter-clockwise until the engine starts to bog down. At this point, turn the screw back clockwise until the engine just starts to run smoothly again.
Now it’s time to adjust the “H” screw. With the saw still running at idle, slowly turn the “H” screw counter-clockwise until the engine starts to race. Again, turn back just until it begins to run smoothly – don’t overdo it or you’ll end up with an engine that won’t idle properly!
Once you’ve fine-tuned both screws, give your chainsaw a test run to see how it’s performing. If all goes well, you should notice an improvement in how smoothly it runs overall.
How Do You Adjust the Carburetor Jets on a Chainsaw?
Chainsaws are one of the most versatile and useful tools that you can have in your arsenal. They can be used for a variety of tasks, from cutting down trees to trimming branches. But like any tool, they need to be properly maintained in order to function at their best.
One of the most important parts of maintaining a chainsaw is adjusting the carburetor jets.
The carburetor jets control the mixture of air and fuel that enters the engine. If these jets are not properly adjusted, it can lead to a number of problems, such as poor engine performance, reduced fuel efficiency, and even damage to the engine.
Fortunately, adjusting the carburetor jets on a chainsaw is relatively easy to do.
First, you’ll need to locate the carburetor adjustment screws. These are usually located near the bottom of the carburetor body (there may be two or three screws depending on your chainsaw model).
Next, start the chainsaw and let it idle for a few minutes so that it’s warm before making any adjustments.
Now, slowly turn each screw clockwise until you hear the engine RPMs begin to drop. Once you’ve found this point, back off each screw about 1/8th of a turn (or until you reach where the RPMs stabilize).
This will ensure that your engine is getting just enough air and fuel mixture for optimal performance without running too rich or too lean.
If you’re still having trouble getting your chainsaw to run correctly after adjusting the carburetor jets, there could be another issue at play (such as an obstructed air filter). However, by following these simple steps you should be able to get your saw running like new again in no time!
How Do You Adjust a Carburetor That is Running Rich?
If your carburetor is running rich, there are a few things you can do to adjust it. First, check the air filter and make sure it is clean. If it is dirty, replace it with a new one.
Next, check the spark plugs and wires to make sure they are in good condition. If they are worn out, replace them. Finally, adjust the carburetor itself by turning the screws clockwise or counterclockwise until the engine runs smoothly.
CORRECT WAY To Adjust Or Tune The Carburetor On A Chainsaw (Step-by-Step)
Chainsaw Won’T Start Carb Adjustment
If your chainsaw won’t start, it could be due to a number of issues. One potential problem is that the carburetor might need adjusting. This is a relatively easy fix that you can do yourself.
Before you begin, make sure that the saw is properly fueled and that the spark plug is in good condition. If both of these things are fine, then it’s likely that the carburetor just needs some adjustment.
The first thing you’ll want to do is locate the screws on the side of the carburetor (there are usually two).
These screws control the amount of fuel and air that enters the engine. To adjust them, simply turn them clockwise or counterclockwise until they’re tight or loose enough (depending on which way you’re going) to create the desired mixture.
If your chainsaw still won’t start after adjusting the carburetor, then there could be another issue at play and you may need to take it to a professional for further diagnosis.
Chinese Chainsaw Carburetor Adjustment
If you’re a chainsaw user, then it’s likely that you will at some point need to adjust the carburetor. This is especially true if you use your chainsaw frequently, as the carburetor can become out of adjustment from normal wear and tear. While most people take their chainsaw to a professional for this type of work, adjusting a Chinese chainsaw carburetor is actually not that difficult and can be done at home with just a few tools.
The first thing you’ll need to do is locate the carburetor on your chainsaw. It’s usually located near the engine, and will have two screws sticking out from it – one for the idle mixture and one for the main jet. The screw for the idle mixture is usually smaller than the main jet screw, so make sure you identify them correctly before adjusting anything.
Once you’ve found the correct screws, start by adjusting the idle mixture screw first. Turn it clockwise until it stops, then turn it counter-clockwise about 1/8 of a turn. This should give you a good starting point for setting your idle mixture.
If your saw seems to run rough after doing this, turn the screw slightly further counter-clockwise until it runs smoothly again.
Next, adjust the main jet screw using the same method as above – turn it clockwise until it stops, then turn it back counter-clockwise about 1/8 of a turn. Again, if your saw seems to run rough after doing this adjustment, simply turn the main jet screw slightly further counter-clockwise until it runs smoothly again.
That’s all there is to adjusting a Chinese chainsaw carburetor!
How to Adjust High And Low on Carburetor
If your carburetor has high and low settings, you may need to adjust them from time to time. Here’s how:
1. Locate the screws on the side of the carburetor that control the high and low settings.
2. Use a screwdriver to turn the screws clockwise or counterclockwise until you achieve the desired setting.
3. Test-drive your vehicle to see if the adjustments have improved its performance.
How to Adjust Stihl Chainsaw Carburetor
If your Stihl chainsaw is running too lean, meaning it’s not getting enough fuel, or too rich, meaning it’s getting too much fuel, you can adjust the carburetor to compensate. It’s important to keep the chainsaw properly tuned because an incorrect mixture can lead to engine damage.
To adjust the carburetor on a Stihl chainsaw, you’ll need a Phillips screwdriver and a flathead screwdriver.
Start by removing the air filter cover and unscrewing the two screws that hold the carburetor in place. Once the carburetor is loose, you can begin adjusting the screws.
The L-screw controls how much fuel goes into the engine and is located on top of the carburetor next to the choke lever.
Turn this screw clockwise to lean out the mixture or counterclockwise to richen it up. The H-screw adjusts how much air flows into the engine and is located on bottom of carburetor next to where the spark plug connects. Turn this screw clockwise to lean out mixture or counterclockwise to richen up mixture.
You may have also noticed an idle speed adjusting knob which sits next to L-screw; however, do not touch this as it should be set at factory default settings.
Now that you know how turn each individual screws, its time for fine tuning your adjustments. First thing you want do after making an adjustment is test run your saw for about 15 seconds then shut off and check your spark plug for coloration changes .
A light brownish color means your running too lean , black means your running too rich , and a dark chocolate brown with no sooty deposits means ideal conditions . If after several adjustments ,you find that there isn’t any change in coloration then its possible one of jets inside carburetors has become clogged in which case you will have clean or replace Carb altogether .
Poulan Chainsaw Carburetor Adjustment
A chainsaw is a mechanical tool that is used to cut through wood. The chain is driven by a motor and the teeth on the chain help to cut through the wood. The carburetor on a chainsaw controls the mixture of air and fuel that goes into the engine.
This mixture needs to be just right in order for the saw to run properly. If the mixture is too rich, it will cause the engine to bog down and if it is too lean, it will cause the engine to overheat.
The carburetor on a Poulan chainsaw can be adjusted manually with a screwdriver.
There are two screws that control the amount of air and fuel that mix together. The high speed screw controls how much fuel enters the carburetor when the saw is running at full throttle while the low speed screw controls how much fuel enters when idle or running at lower speeds. To adjust these screws, you will need a Phillips head screwdriver.
Turning either of these screws clockwise will lean out the mixture while turning them counterclockwise will richen it up. Start with both screws turned all they way in until they bottom out and then back them out 1 1/2 turns as this is usually close to where they need to be set for most saws. If your saw seems like it’s running too hot, turn both screws out 1/4 turn at a time until it runs cooler but don’t go more than 2 turns or you’ll risk damaging your engine from running too lean.
Chainsaw Carburetor Problems
If your chainsaw isn’t starting, the problem may be with the carburetor. Carburetor problems are common, and can be caused by a variety of things such as old or dirty fuel, debris in the carburetor, or a loose spark plug.
If you suspect that the carburetor is the problem, there are a few things you can do to try to fix it.
First, make sure that you’re using fresh, clean fuel. If that doesn’t help, try taking apart the carburetor and cleaning it with compressed air or a small brush. Be careful not to damage any of the delicate parts.
If you’re still having trouble starting your chainsaw, take it to a qualified technician for further diagnosis and repair.
Conclusion
If your chainsaw is running too lean or too rich, you can adjust the carburetor from scratch to fix the problem. First, find the screws on the side of the carburetor that control fuel mixture. Then, turn both screws a quarter-turn in the same direction and test-run your chainsaw.
If it’s still not running right, repeat the process until it does.