If your Poulan chainsaw won’t stay running, there are a few things you can check to troubleshoot the issue. Make sure that the gas and oil mixture in the tank is at the correct level, and that the spark plug is clean and properly gapped. If these things check out, then it’s possible that the carburetor needs to be adjusted or cleaned.
You can try adjusting the idle speed screw first; if that doesn’t work, then you’ll need to remove and clean the carburetor.
If your Poulan chainsaw won’t stay running, there are a few things you can try to fix the problem. First, check the spark plug and make sure it is clean and in good condition. If the spark plug is dirty or damaged, it will need to be replaced.
Next, check the air filter and fuel filter. If either of these are dirty, they will need to be cleaned or replaced. Finally, check the carburetor for dirt or debris.
If you find any, clean it out and see if that fixes the problem.
Poulan Chainsaw Troubleshooting
If your Poulan chainsaw isn’t working properly, there are a few things you can do to troubleshoot the problem. First, check to make sure that the chain is properly lubricated and that the bar isn’t damaged. If the chain is dry or damaged, it will need to be replaced.
You should also check the air filter and spark plug to make sure they’re clean. If the problem persists, you may need to take your chainsaw to a professional for further diagnosis and repair.
Poulan Chainsaw Carburetor Adjustment
A chainsaw is a versatile tool that can be used for a variety of tasks, from felling trees to trimming branches. However, like any piece of machinery, a chainsaw requires regular maintenance to keep it running smoothly. One important aspect of chainsaw maintenance is carburetor adjustment.
The carburetor controls the mixture of air and fuel that enters the engine. If the carburetor is not adjusted properly, the chainsaw will run inefficiently and may even stall. Luckily, adjusting a carburetor is relatively simple and only takes a few minutes.
To adjust the carburetor on a Poulan chainsaw, first locate the screws on the side of the carburetor (there are usually two). These screws are used to adjust the idle speed and throttle response. To adjust the idle speed, turn one of the screws clockwise or counterclockwise until the desired rpm is reached (the optimum rpm range for most Poulan chainsaws is 2200-2600).
To adjust throttle response, turn both screws in or out at the same time until you achieve the desired result.
Once you have finished adjusting the carburetor, start up your chainsaw and let it warm up for a few minutes. Then, test it out by cutting through some wood.
If your chainsaw seems to be running smoothly, then you’ve successfully adjusted the carburetor!
Poulan Pro 42Cc Chainsaw Starts Then Dies
If you’re having trouble getting your Poulan Pro 42cc chainsaw to stay running, there are a few things you can check. First, make sure that the gas and oil mix is at the correct ratio. Too much oil in the mixture can cause the engine to seize up.
Next, check the air filter and spark plug to make sure they’re clean and in good condition. If the problem persists, it’s likely that the carburetor needs to be adjusted or replaced.
Poulan Chainsaw Spark Arrestor
If you’re a chainsaw user, then you know that having a spark arrestor is important. The Poulan brand offers a variety of options when it comes to chainsaws and spark arrestors. In this blog post, we’ll take a closer look at the Poulan brand and what they have to offer when it comes to chainsaws and spark arrestors.
When it comes to chainsaws, Poulan is a well-known name. They’ve been in business for over 70 years and are one of the leading manufacturers of outdoor power equipment. Their products are available in over 140 countries around the world.
When it comes to choosing a Poulan chainsaw, you have plenty of options to choose from depending on your needs. Whether you need a saw for light duty work or something more heavy-duty, there’s sure to be a Poulan model that’s right for you. And if you’re looking for a saw with a spark arrestor, they have several models that offer this feature.
A spark arrestor is an important safety feature on any chainsaw. It helps prevent sparks from escaping the saw and igniting anything nearby, like dry grass or leaves. This can help prevent wildfires from starting unintentionally.
If you’re using your chainsaw in an area where there’s potential for wildfires, then having a spark arrestor is definitely something you should consider. Many states actually require them by law if you’re going to be using your saw in certain areas during fire season. Even if your state doesn’t have this requirement, it’s still something worth considering for your safety and the safety of those around you.
Poulan offers several different models of Chainsaws with Spark Arrestors including: PP4218AVX 18-Inch 42cc 2 Cycle Gas Powered Anti-Vibration Chain Saw With Xtreme Performance Pack; PP5020AV 20-Inch 50cc 2 Cycle Gas Powered Anti-Vibration Chain Saw With Carry Case; And PR5020 20-Inch 50cc 2 Cycle Gas Powered Chain Saw With Carrying Case & 10ft Extension Cord – Perfect For Cutting Firewood & Tree Limbs At Home Or Camping site .
Poulan Chainsaw Factory Carb Settings
If you’re a chainsaw user, then you know that having a properly functioning carb is essential to the saw’s performance. So, what are the factory carb settings for a Poulan chainsaw?
The answer may vary depending on the model of your Poulan saw, but in general, the idle speed screws should be set at 1 3/4 turns out from lightly seated and the main mixture screws should be set two turns out from lightly seated.
These settings are meant as a starting point – you may need to adjust them slightly to get your particular saw running at its best.
If you’re not sure how to adjust the carb on your Poulan chainsaw, consult the owner’s manual or take it to a qualified technician. With just a little bit of care and attention, you can keep your Poulan running like new for years to come!
Why Does My Poulan Chainsaw Dies When I Give It Gas?
If your Poulan chainsaw dies when you give it gas, there are a few possible reasons why. The most common reason is that the carburetor needs to be adjusted. Another possibility is that the spark plug is fouled or damaged.
Here are some tips on how to troubleshoot and fix these problems:
1. Check the carburetor: The most likely cause of your chainsaw dying when you give it gas is that the carburetor needs to be adjusted. To do this, first make sure that the air filter is clean.
Then, remove the chainsaw’s spark plug and unscrew the two screws that hold the carburetor in place. Adjust the idle speed screw until the chainsaw runs smoothly at low speeds. Finally, adjust the high speed screw until the chainsaw runs smoothly at high speeds.
2. Check the spark plug: If adjusting the carburetor doesn’t solve the problem, then check the spark plug. Remove it and inspect it for damage or debris. If it looks damaged, replace it with a new one.
If it’s just dirty, clean it with a wire brush and re-install it.
3. Clean or replace the air filter: Another possible cause of your Poulan chainsaw dying when you give it gas is a dirty or clogged air filter . To clean it , simply remove it from icationthe saw and soakit in some cleaner made specifically for air filters .
Once its fully saturated , scrub any dirt or debris off ofit with an old toothbrush . Rinse well and let dry completely before putting back onthe saw . If its excessively damaged , however , you’ll needto replaceit altogether .
Poulan Chainsaw Won’T Start When Hot
If your Poulan chainsaw won’t start when it’s hot, don’t despair. There are a few things you can try to get it going again. First, check the spark plug to make sure it’s clean and in good condition.
If it looks dirty or damaged, replace it with a new one. Next, check the air filter to see if it needs to be cleaned or replaced. A dirty air filter can block the flow of air to the engine, making it hard for the saw to start.
Finally, make sure that there is fresh gas in the tank and that the oil level is correct. If all of these things check out, then your saw should start right up.

Credit: www.reddit.com
How Do You Fix a Poulan Chainsaw That Won’T Stay Running?
If your Poulan chainsaw won’t stay running, there are a few things you can try to fix the problem. First, check the fuel mixture and make sure it is correct. If it is not, adjust it according to the manufacturer’s instructions.
Next, check the spark plug and clean or replace it if necessary. Finally, inspect the air filter and clean or replace it if needed.
Why Does My Poulan Chainsaw Run Then Quit?
If your Poulan chainsaw starts up and then quits after a few seconds, there are a few potential causes. One possibility is that the fuel isn’t reaching the engine. Check to make sure that the gas tank is full and that there’s no debris blocking the fuel line.
If the problem persists, it could be an issue with the carburetor. Try cleaning it with carburetor cleaner and adjusting the mixture screws.
Another possibility is that the ignition system isn’t working properly.
Check to see if the spark plug is fouled and replace it if necessary. It’s also possible that the coil needs to be replaced. If you’re still having trouble, take your chainsaw to a qualified technician for further diagnosis and repairs.
Why Does My Chainsaw Start But Not Stay Running?
If your chainsaw starts but won’t stay running, there are a few possible causes. First, check the fuel mixture in the gas tank. The correct ratio is 50:1, so if the mixture is too lean (not enough oil), the engine will start but then quickly stall.
Second, check the air filter to make sure it isn’t clogged and restricting airflow to the engine. Third, check the spark plug to see if it needs to be replaced. If none of these things seem to be the problem, take your chainsaw to a qualified technician for further diagnosis and repair.
Why Does My Chainsaw Start And Then Stop?
If your chainsaw starts and then stops, it could be for a number of reasons. Here are some things to check:
1. Is the fuel fresh?
If not, try adding fresh fuel and see if that makes a difference.
2. Is the air filter clean? If not, clean or replace it and see if that helps.
3. Are the spark plug gaps correct? If not, adjust them accordingly and try starting the chainsaw again.
4. Is the saw chain properly tensioned?
If not, adjust it according to the manufacturer’s instructions and try starting the saw again.
5. Finally, if none of these things seem to be the problem, it’s possible that there is an issue with the carburetor or ignition system. In this case, it’s best to take the saw to a professional for diagnosis and repair.
Poulan 3314 won't stay running
Conclusion
The most likely cause of your Poulan chainsaw not staying running is that the carburetor needs to be adjusted. This is a fairly easy adjustment to make, and you should be able to do it yourself with a few simple tools. If you are not comfortable making this adjustment, you can always take it to a local small engine shop or dealer for assistance.