There are two ways to tune a chainsaw with a high and low setting. The first way is to use the adjusting screws on the carburetor to set the idle speed. The second way is to adjust the tension on the chain.
Chainsaws are one of the most versatile and handy tools that you can have in your arsenal. They can be used for a variety of tasks, from cutting down trees to trimming branches. But in order to get the most out of your chainsaw, you need to make sure it is properly tuned.
That’s where the high and low setting comes in.
The high and low setting on a chainsaw refers to the tension on the chain. If the chain is too loose, it can come off the saw while you’re using it.
This can be extremely dangerous. On the other hand, if the chain is too tight, it can cause the motor to overheat and potentially damage the saw. So finding that perfect balance is crucial.
To tune your chainsaw, start by putting it on a level surface. Then, check that the bar is level with the ground. Next, adjust the tension on the chain so that there is about 1/8 inch of play when you push down on it with your thumb (this may vary depending on your saw).
Once you’ve got that set, fire up your saw and give it a test run!

Credit: deerassociation.com
How Do You Adjust the H And L on a Chainsaw?
There are two ways to adjust the H and L on a chainsaw. The first is to use the adjusting screws that are located on the side of the chainsaw near the bottom. The second way is to loosen the bar nuts and turn the bar to the desired position.
What are the L And H on Chainsaw?
If you’re a chainsaw user, then you’re probably familiar with the terms “L” and “H.” But what do they mean? Let’s take a look.
The “L” on a chainsaw stands for low kickback. This means that the chainsaw is designed to reduce the risk of kickback, which is when the chain suddenly stops and reverses direction. Kickback can be dangerous, so it’s important to choose a saw with low kickback if you’re going to be using it regularly.
The “H” on a chainsaw stands for high power. This means that the saw has more power than other models in its class. If you need to cut through thick materials or make large cuts, then you’ll want to choose a saw with high power.
Keep in mind that these saws will also be heavier and more difficult to handle, so make sure you’re comfortable with them before using them.
What are the H And L Setting on Stihl Chainsaw?
If you’re a chainsaw user, then you’re probably familiar with the H and L settings. These two settings adjust the amount of oil that is released onto the chain while it’s in use. The “H” setting stands for high and releases more oil, while the “L” setting stands for low and releases less oil.
So, what’s the difference between these two settings? And when should you use each one? The main difference between the H and L settings is the amount of oil that is released onto the chain.
The H setting will release more oil than the L setting. This is because when you’re using the chainsaw on high-load tasks (like cutting through thick wood), more lubrication is needed to keep the chain running smoothly. On the other hand, when you’re doing lighter work (like trimming branches), less lubrication is needed and so the L setting can be used.
In general, it’s best to use the H setting when you’re doing heavier work and the L setting when you’re doing lighter work. However, there are some exceptions to this rule. For example, if your chainsaw has an automatic oiling system, then you’ll want to use whichever setting results in less smoke coming from the exhaust (since too much oil can cause excessive smoking).
Also, if your saw has an adjustable bar depth control, then using a shallower bar depth combined with a higher Chainspeed (CS)Setting will minimize frictional heat build-up within cuts thereby reducing wear on both saw chain components as well as guide bar rails. In addition, If conditions are exceptionally dry, dusty, or hot, operating at a lower bar-oil flow rate may help prevent premature dulling due to increased friction. Conversely, If conditions are extremely cold or wet, increasing your saw’s bar-oil flow rate may help maintain cutting efficiency by keeping working surfaces adequately lubricated.
How Do You Adjust a Carburetor That is Running Rich?
A carburetor that is running rich means that the mixture of air and fuel in the engine is too heavy on fuel. This can happen for a number of reasons, but most commonly it is because the carburetor needs to be adjusted. There are a few ways to adjust a carburetor, depending on what type of carburetor it is and how accessible it is.
If you have an adjustable carburetor, the first step is to turn the adjusting screw clockwise until it stops. Then back off the screw 1/4 turn. This will usually lean out the mixture enough to fix the problem.
If your carburetor does not have an adjusting screw, then you will need to remove the float bowl and manually bend the float tang to lower the float level. This will also lean out the mixture and should fix your problem.
It is also important to check for any vacuum leaks when troubleshooting a rich running condition.
A vacuum leak will introduce more air into the system and throw off the ratio of air to fuel. Make sure all of your intake manifold gaskets are in good shape and there are no cracks or holes in your intake hose before moving on to other possible causes.
Episode 28: Chainsaw Carburetor Adjustment Tuning | How to Tune ‘Correctly’
How to Adjust High And Low on Carburetor
If you have ever wondered how to adjust the high and low settings on a carburetor, wonder no more! This guide will show you everything you need to know about adjusting these settings so that your engine runs more efficiently. The first thing you need to do is locate the screws that control the high and low settings.
On most carburetors, these screws will be located near the bottom of the carburetor, on either side of the bowl. Once you have found these screws, label them so that you know which is which. Next, it’s time to start making adjustments.
To adjust the high setting, turn the screw clockwise until the engine RPMs increase. Then, back off the screw slightly until the RPMs level off. For best results, repeat this process several times until you find the sweet spot.
To adjust the low setting, turn the screw counterclockwise until the engine starts to sputter and stall. Then, back off the screw slightly until it runs smoothly again. As with the high setting, it’s best to repeat this process several times until you find just the right mixture.
Now that you know how to adjust both your high and low settings on your carburetor, it’s time to fine-tune your engine for optimal performance!
Poulan Chainsaw High Low Adjustment
If you’re a chainsaw user, then you know that having a properly adjusted chain is key to getting the best performance out of your saw. And if you’re a Poulan user, then you know that adjusting the chain on your Poulan saw is a little different than on other brands. Here’s a quick guide to adjusting the high and low settings on the Poulan chainsaw.
First, locate the adjustment screws on the side of the saw near the bottom front. There will be two screws, one for high and one for low. For most models, turning the screw clockwise will raise the setting, while counterclockwise will lower it.
With the engine off and cool, turn both screws all the way in (clockwise) until they stop. This is your starting point. Now slowly back out (counterclockwise) each screw about 1/8 of a turn at a time until you reach your desired setting.
Once you’ve found the right setting, tighten down each screw so it doesn’t move during use. And that’s all there is to it! Adjusting your Poulan chainsaw’s high and low settings is easy once you know where to look and in which direction to turn the screws.
Chainsaw Won’t Start Carb Adjustment
If your chainsaw won’t start, one possible reason is that the carburetor needs adjustment. This is a relatively simple task that you can do yourself, and it may just be the thing that gets your chainsaw up and running again. To adjust the carburetor on your chainsaw, first, make sure that the saw is turned off and the spark plug is disconnected.
Then, remove the air filter cover so you can access the carburetor. Locate the screws labeled “H” and “L” – these are the high and low-speed screws. Turning the “H” screw clockwise will lean out the mixture of fuel and air, while turning it counterclockwise will richen the mixture.
Similarly, turning the “L” screw clockwise will richen the mixture while turning it counterclockwise will lean it out. Start by adjusting both screws a quarter turn at a time in opposite directions – for example, turn one a quarter turn clockwise while turning the other a quarter turn counterclockwise. If this doesn’t seem to be having any effect, then try making bigger adjustments until you find something that works.
Once you’ve found a combination of settings that seems to work well, replace the air filter cover and reconnect the spark plug. Try starting up your chainsaw again – if it’s still not working properly, then repeat this process until you get it running right.
Chainsaw High Low Adjustment Tool
Chainsaw high-low adjustment tools are designed to help you adjust the tension on your chainsaw chain. They come in a variety of sizes and designs, but all serve the same purpose. The most important thing to know about using one of these tools is that you must always use gloves when handling it.
This is because the tool can cause serious injury if used improperly. Always follow the manufacturer’s instructions when using this tool. And, be sure to keep your fingers away from the moving parts of the chainsaw while you’re working.
Stihl Factory Carb Settings
If you’re a fan of Stihl products, you know that they’re some of the best in the business. But what you might not know is that every Stihl factory carburetor is set to specific settings. That’s because each engine is designed for a certain range of power and torque output.
That means that if you try to adjust your carburetor without knowing the proper settings, you could end up damaging your engine. So before you make any adjustments, be sure to check with your local Stihl dealer or service center for the correct settings.
Chinese Chainsaw Carburetor Adjustment
If you’re a fan of chainsaws, then you know that having a well-tuned machine is essential to getting the job done right. The same goes for your saw’s carburetor – if it’s not properly adjusted, your saw will run poorly (or not at all). Fortunately, adjusting a carburetor on a Chinese chainsaw is relatively easy.
With just a few simple tools and some basic knowledge, you can get your saw running like new in no time. Here’s what you’ll need to adjust your carburetor: -A screwdriver
-A small wrench or pliers (for adjusting the idle speed screw) -A feeler gauge (for setting the air gap) -Patience!
First, locate the adjustment screws on the carburetor. There are typically three screws – one for idle speed, one for low-speed mixture, and one for high-speed mixture. Consult your owner’s manual to be sure.
unscrew the idle mixture needle until it is flush with the bottom of its housing. This will give you more room to work with when making adjustments later on. Next,.
This will give you more room to work with when making adjustments later on. Now it’s time to set the air gap between the flywheel and magnets. This gap must be within 0.004″-0.006″ or else your engine may suffer damage over time.
Use a feeler gauge to measure the gap – if it’s too wide, use a smaller gauge; if it’s too narrow, use a larger gauge..005″. With the air gap set, you can now adjust the idle mixture screw.. Turn it clockwise until it lightly bottoms out, then back off 1/8 turn. This will ensure that your engine is getting enough fuel at idle without flooding itself. If your engine stalls or runs rough at idle after this adjustment, turn the screw another 1/8 turn counterclockwise.
Chainsaw Adjustment Screws
Chainsaw adjustment screws are one of the most important aspects of maintaining your saw. By making sure these screws are properly adjusted, you can keep your chainsaw running at its peak performance. There are three different types of adjustment screws on a chainsaw: idle speed, carburetor mixture, and chain tension.
Idle speed screw: This adjusts the engine speed when the saw is idling. If this screw is too loose, the engine will race when idling. If it’s too tight, the engine will bog down and may stall.
Carburetor mixture screw: This regulates the fuel/air mixture in the carburetor. A lean mix will result in less power and can cause damage to the engine over time, while a rich blend will cause excessive smoke and could lead to an explosion. Chain tension screw: This is probably the most important adjustment screw on the saw.
A loose chain can slip off the bar and cause serious injury, while a too-tight chain will put unnecessary strain on the motor and decrease cutting performance.
How to Tune a Husqvarna Chainsaw
If you’re a fan of Husqvarna chainsaws, then you know that they’re some of the best in the business. But even the best chainsaw can’t perform at its peak if it’s not properly tuned. In this blog post, we’ll show you how to tune a Husqvarna chainsaw so that it runs like new.
First, start by checking the air filter. A clean air filter is essential for optimal performance, and it’s easy to check and replace if necessary. Just remove the cover and look for any dirt or debris.
If the filter is dirty, replace it with a new one. Next, take a look at the spark plug. The spark plug needs to be replaced every few months to ensure optimal performance.
To check it, remove the plug and inspect it for any damage or deposits. If it looks damaged or dirty, replace it with a new one. Now let’s move on to the chain itself.
The first thing you’ll want to do is make sure that it’s properly tensioned. This can be done by hand – just pull on the chain from both ends and see if there’s any slack in it. If there is, use the adjustment screws on either side of the saw to tighten things up until there’s no more slack in the chain.
Finally, sharpen your chain regularly using a sharpening stone or file. This will keep your cuts clean and prevent your saw from getting bogged down mid-cut. And that’s all there is to tuning a Husqvarna chainsaw!
By following these simple steps, you can keep your saw running like new for years to come.
Conclusion
The chainsaw is an important tool for anyone who needs to cut down trees or limbs. It is a powerful and dangerous tool, so it is important to know how to properly operate and maintain it. One of the most important aspects of chainsaw maintenance is keeping the chain sharp.
A dull chain can cause the saw to bind, making it difficult to control. It can also cause kickback, which can be very dangerous. There are two ways to sharpen a chainsaw chain: with a high setting and a low setting.
The high setting is used for general-purpose cutting and the low setting is used for precision cutting. To sharpen the chain, you will need a file, some gloves, and safety goggles. First, put on the gloves and safety goggles.
Then, find the link that you want to sharpen and hold it so that the teeth are pointing up. Place the file against the tooth at a 45-degree angle and push forward until you feel resistance. then, pull back towards you without lifting the file off of the tooth.